Type: Driver
File Name:
File Size: 35.5 MB
28 (4.59)
Downloads: 16
Supported systems: Windows XP, Windows Vista, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10, Windows 10 64 bit
Price: Free* (*Free Registration Required)

Download Now

Available from these sellers. This fits your.

Customers also shopped for. Please contact us to complete your request. The intended current must be less than 8.

Remove the ammeter and variable resistor from your circuit. Measure the resistance of the variable resistor. The measured resistance is the ideal value of the pull-up resistor. Select a static resistor value for your pull-up resistor that is greater than or equal to the ideal resistance. Reconnect the load national instruments ni usb-6009 and the pull-up resistor.

Do not exceed the specified current output limits of the DAQ device. National Instruments has several signal conditioning national instruments ni usb-6009 for digital applications requiring high current drive. Always properly ground yourself and the equipment when handling the DAQ device or connecting to it.

fuji finepix s602z usbMultifunction I/O Device
hp wan miniport l2tpProduct Description
epson lq 590 esc p 2 ver 2.0Introduction, User guide and specifications

Not just a picture from the manufacturer's website, but the actual piece of equipment you would receive. Lu, L. A valid service agreement may be required, and support options vary national instruments ni usb-6009 country. Compared to Simple LV71, this example can allow you to set the sampling rate and to change the showing status of Origin 8. If you need to clean the device, use a dry cloth. Look for the marks on the product label for verification of certification. Well, what if you were able to see a piece of equipment before you purchased it?


I have also tried "addDigitalChannel" but I receive an error stating that this is not possible for the given daq. Open the.

National Instruments NI USB-6009 User Manual

Getting Started Resources. This software will NOT. Hi, I have c-DAQ which i have been using for one of my project national instruments ni usb-6009 three years national instruments ni usb-6009. NI-DAQmx v Now I have somet. The most recent setup file that can be downloaded is 1. One of our friendly Customer Service representatives will be contacting you shortly with information on when the equipment you requested will be available for viewing.


If a grounded signal source is incorrectly measured, this difference can appear as measurement error. Follow the connection instructions for grounded signal sources to eliminate this ground potential difference from the measured signal. Use differential connections instead. As shown in the bottom-rightmost cell of Table 6, there can be a potential difference between GND and the ground of the sensor. In RSE mode, this ground loop causes measurement errors. The differential input mode can measure 20 V signals in the 20 V range. However, the maximum voltage on any one pin is 10 V with respect to GND. When no signals are connected to the national instruments ni usb-6009 input terminal, the internal resistor divider may cause the terminal to float national instruments ni usb-6009 approximately 1.

This behavior is normal and does not affect the measurement when a signal is connected. All updates of analog output channels are software-timed. GND is the ground-reference signal for the analog output channels. There is national instruments ni usb-6009 DAC for each analog output line.

National Instruments NI USB User Manual 32 pages Also for: NI USB

These glitches are normal; when a DAC switches from one voltage to another, it produces glitches due to released charges. The largest glitches occur when the most significant bit of the DAC code changes. You can build a lowpass deglitching filter to remove some of these national instruments ni usb-6009, depending on the national instruments ni usb-6009 and nature of the output signal. Page 10 Before installing the device, you must install the software you plan to use with the device.

Refer to the and the documentation included with the software for more information.8 AI (Bit, 48 kS/s), 2 AO ( Hz), 13 DIO USB Multifunction I/O Device —The USB‑ is a low-cost, multifunction DAQ device. It offers analog I/O, digital I/O. This user guide describes how to use the National Instruments USB and National Instruments USB national instruments ni usb-6009 acquisition (DAQ) devices. The NI.

Other Drivers

Leave a Reply

Your email address will not be published. Required fields are marked *